Blueridge mini split error code C5
Jumper cap malfunction (missing or wrong jumper).
- TypeFault
- SystemControl board
- Can I fix it?Homeowner checks, then maybe a tech
- Applies toBMKH series (Gree-built)
What C5 means on a Blueridge
Gree indoor boards use a small plug-in jumper that tells the board which model it is. The board cannot find it, or it is the wrong one. This almost always happens after a board replacement or a service visit.
On this platform, C5 is a fault: something has failed or is disconnected and needs diagnosis.
Common causes
- The jumper was left off after board work.
- The wrong jumper was installed.
- The jumper's socket is corroded or damaged.
How to fix it yourself
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician.
- With power off, open the indoor electrical box and look for a small plug-in jumper on the main board (often labelled JUMP).
- Reseat it firmly. If the board was replaced, move the jumper from the old board to the new one.
- Reset the system: switch the breaker (or the outdoor disconnect) off, wait a full five minutes so the boards fully discharge, then switch it back on and restart from the remote.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
If the jumper is present and seated, the board needs a technician's attention.
Which Blueridge units show C5
This page applies to Blueridge BMKH wall-mount, floor-ceiling and multi-zone (2016 and later) and BMY / BMX S-series single-zone (2023 and later) units on the BMKH series (Gree-built). Blueridge's own documentation lists C5 as "Jumper cap malfunction (missing or wrong jumper)", the same definition used across the Gree platform it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where Blueridge shows this code
BMKH series (Gree-built): The code shows on the indoor unit's display in place of the temperature. If the display is off, press the Light button on the remote. Some models also count out the code as indicator blinks. E codes are system protections and faults, F codes are mostly sensor faults, H codes are outdoor and compressor protections, U codes are motor and valve faults, and P codes are power-supply faults.
Other Blueridge codes
Same part of the system as C5:
C5 on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
Questions people ask
Can I reset a Blueridge C5 code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If C5 comes back, the fault is real and needs the checks above.
Is it safe to keep running a Blueridge showing C5?
The unit will usually refuse to run, or run with reduced output, until the fault is cleared. Repeated resets do not fix anything and can mask a problem that is getting worse.
Do I need a technician for Blueridge C5?
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician. If the jumper is present and seated, the board needs a technician's attention.
Sources
- Blueridge Installation and Owner's Manual (BMKH, 11/2016 and 01/2017 editions), Diagnostic Codes
- Blueridge BMKH Floor-Ceiling User and Install Manual (12/2023), error code table
- Blueridge BMY19 Series Owner's Manual and DIY Single Zone Installation Manual (2020), Midea document CS78421-548-754 (same manual family as Pioneer WYT)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.