Blueridge mini split error code PL
DC bus low voltage (under-voltage) protection.
- TypeProtection
- SystemPower supply
- Can I fix it?Homeowner checks, then maybe a tech
- Applies toBMKH series (Gree-built)
What PL means on a Blueridge
The DC bus voltage fell below its limit and the compressor stopped. Usually supply voltage sagging under load.
On this platform, PL is a protection: the system stopped or throttled itself to prevent damage; many clear on their own once conditions return to normal.
Common causes
- Utility voltage sag or brownout.
- An undersized generator, extension cord or wire run.
- A loose power connection dropping voltage under load.
- A failed capacitor on the outdoor board.
How to fix it yourself
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician.
- Reset the system: switch the breaker (or the outdoor disconnect) off, wait a full five minutes so the boards fully discharge, then switch it back on and restart from the remote.
- If you own a multimeter and are comfortable using it, measure the supply voltage at the outdoor unit's L1 and L2 terminals with the unit running. A 230 V system should read roughly 208 to 253 VAC.
- With power off, tighten every power connection from breaker to outdoor unit.
- If it trips when other big loads start, have an electrician check the circuit.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
Normal supply voltage and tight connections with a persistent PL means the outdoor board's power section.
Which Blueridge units show PL
This page applies to Blueridge BMKH wall-mount, floor-ceiling and multi-zone (2016 and later) and BMY / BMX S-series single-zone (2023 and later) units on the BMKH series (Gree-built). Blueridge's own documentation lists PL as "DC bus low voltage (under-voltage) protection", the same definition used across the Gree platform it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where Blueridge shows this code
BMKH series (Gree-built): The code shows on the indoor unit's display in place of the temperature. If the display is off, press the Light button on the remote. Some models also count out the code as indicator blinks. E codes are system protections and faults, F codes are mostly sensor faults, H codes are outdoor and compressor protections, U codes are motor and valve faults, and P codes are power-supply faults.
Other Blueridge codes
Same part of the system as PL:
PL on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
- Gree PL DC bus low voltage (under-voltage) protection
Questions people ask
Can I reset a Blueridge PL code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If PL comes back, the fault is real and needs the checks above.
Is it safe to keep running a Blueridge showing PL?
Not repeatedly. A protection code means the unit stopped itself to prevent damage, and resetting it over and over can turn a cheap repair into a compressor failure. Reset once, check the basics, and stop if it returns.
Do I need a technician for Blueridge PL?
Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician. Normal supply voltage and tight connections with a persistent PL means the outdoor board's power section.
Sources
- Blueridge Installation and Owner's Manual (BMKH, 11/2016 and 01/2017 editions), Diagnostic Codes
- Blueridge BMKH Floor-Ceiling User and Install Manual (12/2023), error code table
- Blueridge BMY19 Series Owner's Manual and DIY Single Zone Installation Manual (2020), Midea document CS78421-548-754 (same manual family as Pioneer WYT)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.