Comfortmaker mini split error code oE
Outdoor unit fault (see outdoor board). Also shown as OE, 0E.
- TypeFault
- SystemOperation
- Can I fix it?Technician job
- Applies toDLC4 / DLF4 series, 2013 to 2015 (Gree-built)
What oE means on a Comfortmaker
The indoor unit is reporting that the outdoor unit has a fault it is not detailing. The specific fault shows as LED blinks or a code on the outdoor control board.
On this platform, oE is a fault: something has failed or is disconnected and needs diagnosis.
Common causes
- Any outdoor-side protection or fault.
How to fix it yourself
Do the reset and the visual checks, but the underlying repair needs a technician with a meter and the service manual.
- Reset the system: switch the breaker (or the outdoor disconnect) off, wait a full five minutes so the boards fully discharge, then switch it back on and restart from the remote.
- Look at the outdoor unit: clear leaves, cottonwood fluff, snow or ice from the coil and make sure the fan can spin freely and nothing is stacked against the cabinet.
- With power off, open the outdoor service panel and look for a status LED blink count or a code on the outdoor board; the service manual decodes it.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
Outdoor board diagnosis is a technician job.
Which Comfortmaker units show oE
This page applies to Comfortmaker DLCSRA / DLCSRB / DLCLRA outdoor with DLFSHA / DLFSFA indoor (2015 and later) and DLC4 / DLF4 (2013 to 2015) units on the DLC4 / DLF4 series, 2013 to 2015 (Gree-built). Comfortmaker's own documentation lists oE as "Outdoor unit fault (see outdoor board)", the same definition used across the Gree platform it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where Comfortmaker shows this code
DLC4 / DLF4 series, 2013 to 2015 (Gree-built): The code shows on the indoor unit's display in place of the temperature. If the display is off, press the Light button on the remote. Some models also count out the code as indicator blinks. E codes are system protections and faults, F codes are mostly sensor faults, H codes are outdoor and compressor protections, U codes are motor and valve faults, and P codes are power-supply faults.
Other Comfortmaker codes
Same part of the system as oE:
oE on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
- Blueridge oE Outdoor unit fault (see outdoor board)
Questions people ask
Can I reset a Comfortmaker oE code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If oE comes back, the fault is real and needs the checks above.
Is it safe to keep running a Comfortmaker showing oE?
The unit will usually refuse to run, or run with reduced output, until the fault is cleared. Repeated resets do not fix anything and can mask a problem that is getting worse.
What will a technician check for oE?
Outdoor board diagnosis is a technician job. Ask for the measurements, not just a parts quote.
Sources
- ICP DLCSRA Outdoor Unit Single Zone Ductless Service Manual 32808000801 (error code table)
- ICP ductless installation instructions IM-KSAIC04-04 (DLCPRA / DLCSRB / DLCERB / DLCLRA error codes)
- ICP R-410A Ductless Split System Service Manual 421 01 9204 00 (DLC4 / DLF4, 2013)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.