KeepRite mini split error code E9
Indoor unit water-full (drain) protection.
- TypeProtection
- SystemCondensate drain
- Can I fix it?Usually a homeowner fix
- Applies toDLC4 / DLF4 series, 2013 to 2015 (Gree-built)
What E9 means on a KeepRite
The condensate level in the indoor unit is too high (a float switch tripped). The unit stops cooling so it does not overflow. Applies to units with a drain pump or float switch.
On this platform, E9 is a protection: the system stopped or throttled itself to prevent damage; many clear on their own once conditions return to normal.
Common causes
- A blocked or kinked condensate drain.
- A drain line without continuous fall.
- A failed condensate pump.
- A stuck float switch.
How to fix it yourself
You can almost always clear this yourself with the steps below.
- Confirm water flows from the drain outlet while cooling.
- Clear the drain with a wet/dry vacuum at the outlet.
- Check the drain line for dips.
- If a pump is fitted, check it runs and the float moves freely.
Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.
When to call a technician
A technician can replace a failed pump or float switch.
Which KeepRite units show E9
This page applies to KeepRite DLCSRA / DLCSRB / DLCLRA outdoor with DLFSHA / DLFSFA indoor (2015 and later) and DLC4 / DLF4 (2013 to 2015) units on the DLC4 / DLF4 series, 2013 to 2015 (Gree-built). KeepRite's own documentation lists E9 as "Indoor unit water-full (drain) protection", the same definition used across the Gree platform it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.
Where KeepRite shows this code
DLC4 / DLF4 series, 2013 to 2015 (Gree-built): The code shows on the indoor unit's display in place of the temperature. If the display is off, press the Light button on the remote. Some models also count out the code as indicator blinks. E codes are system protections and faults, F codes are mostly sensor faults, H codes are outdoor and compressor protections, U codes are motor and valve faults, and P codes are power-supply faults.
Other KeepRite codes
E9 on other brands
The same characters do not always mean the same thing. Check the brand on your unit.
- Blueridge E9 Indoor unit water-full (drain) protection
- Zone Air E9 Outdoor IPM or compressor drive fault
- Mitsubishi Electric E9 Communication error between indoor and outdoor units
- Trane E9 Outdoor IPM or compressor drive fault / Communication error between indoor and outdoor units
Questions people ask
Can I reset a KeepRite E9 code myself?
Yes. Turn the system off at the breaker for five minutes, then restart it. If E9 comes back, the fault is real and needs the checks above.
Is it safe to keep running a KeepRite showing E9?
Not repeatedly. A protection code means the unit stopped itself to prevent damage, and resetting it over and over can turn a cheap repair into a compressor failure. Reset once, check the basics, and stop if it returns.
Do I need a technician for KeepRite E9?
You can almost always clear this yourself with the steps below. A technician can replace a failed pump or float switch.
Sources
- ICP DLCSRA Outdoor Unit Single Zone Ductless Service Manual 32808000801 (error code table)
- ICP ductless installation instructions IM-KSAIC04-04 (DLCPRA / DLCSRB / DLCERB / DLCLRA error codes)
- ICP R-410A Ductless Split System Service Manual 421 01 9204 00 (DLC4 / DLF4, 2013)
Updated September 2026. Codes and definitions vary by model year. If your manual disagrees with this page, your manual wins. Send a correction.