Lennox mini split error code E1

Common causes

• Interconnect wires not landed in the same order at both ends (a swapped signal and neutral is the classic).
• A loose or backed-out terminal screw, or a strand of wire not fully under the screw.
• A damaged, spliced or undersized communication cable (it must be a continuous run of the correct gauge).
• No power at the outdoor unit: a tripped breaker, an open disconnect or a blown fuse.
• A failed outdoor control board or a blown board fuse, often after a lightning event or a power surge.
• On multi-zone systems, one indoor unit's cable landed on the wrong outdoor terminal block (A, B, C).

How to fix it yourself

Work through the checks below first; they resolve most cases. If they do not, the repair itself may need a technician.

1. Reset the system: switch the breaker (or the outdoor disconnect) off, wait a full five minutes so the boards fully discharge, then switch it back on and restart from the remote.
2. Confirm the outdoor unit actually has power. Check the breaker, the disconnect and any fuse in the disconnect box.
3. With power off, open the terminal covers on both units and check the interconnect wiring. Each numbered terminal must land on the same number at both ends, every strand must be under its screw, and there must be no splices, nicks or reversed conductors.
4. Make sure the communication wire is a solid, continuous run of the gauge the manual specifies. Extending it with a wire nut or using a lighter gauge is a frequent cause of intermittent errors.
5. If you own a multimeter and are comfortable using it, measure the supply voltage at the outdoor unit's L1 and L2 terminals with the unit running. A 230 V system should read roughly 208 to 253 VAC.
6. If the wiring checks out and the outdoor unit has power, look for LED fault lights on the outdoor control board (behind the service panel). A dark board with good supply voltage usually means a blown board fuse or a dead board.

Switch off power at the breaker before opening either unit. Capacitors in the outdoor unit hold a charge for several minutes after power is cut.

When to call a technician

Call a technician if the wiring is verified correct and the outdoor unit has power but the code persists. Board diagnosis needs the service manual and a meter.

Which Lennox units show E1

This page applies to Lennox MPA / MPB / MLA single-zone, MPA / MPB / MLA multi-zone, MCB / MWCB, MWMA / MWMB, MCFA / MCFB and MMDA / MMDB units on the MPA / MPB / MLA indoor unit display. Lennox's own documentation lists E1 as "Communication error between indoor and outdoor units", the same definition used across the Midea platform (classic codes) it is built on. If your unit shows a code with a different shape (for example a four-character code, or a plain number), it is from a different table; use the lookup with your exact code.

Where Lennox shows this code

MPA / MPB / MLA indoor unit display: The code appears on the indoor unit's LED display in place of the set temperature. Some models also blink the indicator lamps in a pattern that matches the code. E codes are faults in the indoor unit or its communication link, F codes are faults on the outdoor side, and P codes are protections: the outdoor unit has stopped itself to prevent damage. EC is the refrigerant leak check.

Other Lennox codes

Same part of the system as E1:

All Lennox error codes

E1 on other brands

The same characters do not always mean the same thing. Check the brand on your unit.

• Pioneer E1 Communication error between indoor and outdoor units
• Blueridge E1 High pressure protection / Communication error between indoor and outdoor units
• Gree E1 High pressure protection
• Zone Air E1 Indoor room temperature sensor fault (open or short circuit)
• Daikin E1 Outdoor unit control board (PCB) failure
• Mitsubishi Electric E1 Remote controller control board fault
• Trane E1 Indoor room temperature sensor fault (open or short circuit) / Remote controller control board fault
• Heil E1 Communication error between indoor and outdoor units / High pressure protection
• ACiQ E1 Communication error between indoor and outdoor units / Indoor room temperature sensor fault (open or short circuit)